Optimization Research of SGTR Procedure for Nuclear Power Plant
-
摘要: 核电厂通过应急运行规程(EOP)来缓解蒸汽发生器传热管破裂(SGTR)事故,SGTR事故分析结果显示,在缓解过程中操纵员开启稳压器卸压阀进行反应堆冷却剂系统(RCS)降压后,安全注射(简称“安注”)流量大幅增加,导致稳压器水位大幅增加,可能存在潜在的危险。本文目的是为了更好地缓解SGTR事故,使事故缓解过程中稳压器水位不致上升过高,确保核电厂安全。通过对EOP缓解步骤进行优化,提前切除一列安注,并对优化后的EOP缓解事故过程进行分析计算,最终结果显示稳压器最高水位下降,减少了稳压器水位过高的风险,为后续核电厂规程的改进提供了依据。
-
关键词:
- 蒸汽发生器传热管破裂(SGTR) /
- 应急运行规程(EOP)优化 /
- 稳压器水位 /
- 安注系统
Abstract: Nuclear power plant mitigates SGTR accident by emergency operating procedure (EOP). SGTR analysis results show that after the operator opens the pressurizer relief valve to decrease reactor coolant system pressure in the process of accident mitigation, the safety injection flow increases quickly causing the pressurizer level increasing substantially, there may be a potential danger. The purpose of this paper is to better mitigate the SGTR accident, so that the pressurizer level will not rise too high during the accident mitigation process to keep the nuclear power plant safe. By optimizing the EOP mitigation steps, cutting off a row of safety injection in advance, and analyzing and calculating the accident mitigation process of the optimized EOP, the final results show that the maximum level of the pressurizer decreases, which reduces the risk of excessive level of the pressurizer, which provides a basis for the follow-up improvement of the nuclear power plant procedure. -
表 1 SGTR事件序列(规程修改前)
Table 1. SGTR Sequence of Events (before Procedure Modified)
事件 时间/s SGTR事故发生 0 触发稳压器低压力停堆信号(停堆整定值)(A) 258.7 反应堆紧急停堆(A) 260.7 汽轮机停机(A) 260.7 主泵开始惰转(A) 260.7 破损SG卸压阀第一次开启(A) 266.5 完好SG卸压阀第一次开启(A) 267.1 触发稳压器低压力安注信号(安注整定值)(A) 278.2 主给水关闭(A) 280.2 辅助给水启动(A) 285.2 安注系统投入(A) 298.2 关闭破损SG主蒸汽隔离阀(O) 878.2 终止破损SG辅助给水(O) 978.2 打开完好SG环路的主蒸汽大气释放阀(O) 1078.2 关闭完好SG环路的主蒸汽大气释放阀(O) 1664.4 开启稳压器卸压阀(O) 1764.4 关闭稳压器卸压阀(O) 1910.0 切除安注(O) 2010.0 实施稳压器辅助喷淋(O) 2110.0 破口流量终止 2238.0 计算结束 2500.0 (A)—自动动作;(O)—操纵员手动操作,下同 表 2 SGTR事件序列(规程修改后)
Table 2. SGTR Sequence of Events (after Procedure Modified)
事 件 时间/s SGTR事故发生 0 触发稳压器低压力停堆信号(停堆整定值)(A) 258.7 反应堆紧急停堆(A) 260.7 汽轮机停机(A) 260.7 主泵开始惰转(A) 260.7 破损SG卸压阀第一次开启(A) 266.5 完好SG卸压阀第一次开启(A) 267.1 触发稳压器低压力安注信号(安注整定值)(A) 278.2 主给水关闭(A) 280.2 辅助给水启动(A) 285.2 安注系统投入(A) 298.2 关闭破损SG主蒸汽隔离阀(O) 878.2 终止破损SG辅助给水(O) 978.2 打开完好SG环路的主蒸汽大气释放阀(O) 1078.2 关闭完好SG环路的主蒸汽大气释放阀(O) 1664.4 关闭一列安注(O) 1764.4 开启稳压器卸压阀(O) 1864.4 关闭稳压器卸压阀(O) 1995.0 切除安注(O) 2095.0 实施稳压器辅助喷淋(O) 2195.0 破口流量终止 2310.0 计算结束 2500.0 -
[1] 叶成,郑明光,王勇,等. AP1000应急运行规程接口分析[J]. 核动力工程,2013, 34(3): 164-167,174. doi: 10.3969/j.issn.0258-0926.2013.03.039 [2] LIU L X. Research on impact of pressurizer heater block on SGTR overfill analysis[C]//2017 25th International Conference on Nuclear Engineering. Shanghai, 2017: 2-4. [3] 柯晓. CAP1000核电厂全功率范围SGTR事故研究[J]. 原子能科学技术,2014, 48(6): 1031-1037. doi: 10.7538/yzk.2014.48.06.1031 [4] MARSH L B. Evaluation of steam generator tube rupture events: NUREG-0651[R]. Washington: NRC, 1980. [5] 蒋孝蔚,邓坚,邱志方,等. 安全壳背压对SGTR事故进程的影响研究[J]. 核动力工程,2019, 40(5): 180-183. [6] 刘立欣,刘展. SGTR事故SG满溢分析扩展研究[J]. 核动力工程,2020, 41(3): 81-85.