FE Simulation of Bolt-up Process for Press-Retraining Bolts of HTR-PM Pressure Vessel

ZHANG Tian-yi; WAN Li; SHI Li; ZHANG Chuan-yong

Volume 32 Issue S1

Mar. 2025

Turn off MathJax

Article Contents

Abstract

References

Article Navigation > Nuclear Power Engineering > 2011 > 32(S1): 54-56

ZHANG Tian-yi, WAN Li, SHI Li, ZHANG Chuan-yong. FE Simulation of Bolt-up Process for Press-Retraining Bolts of HTR-PM Pressure Vessel[J]. Nuclear Power Engineering, 2011, 32(S1): 54-56.

Citation:

ZHANG Tian-yi, WAN Li, SHI Li, ZHANG Chuan-yong. FE Simulation of Bolt-up Process for Press-Retraining Bolts of HTR-PM Pressure Vessel[J]. Nuclear Power Engineering, 2011, 32(S1): 54-56.

ZHANG Tian-yi, WAN Li, SHI Li, ZHANG Chuan-yong. FE Simulation of Bolt-up Process for Press-Retraining Bolts of HTR-PM Pressure Vessel[J]. Nuclear Power Engineering, 2011, 32(S1): 54-56.

Citation:

ZHANG Tian-yi, WAN Li, SHI Li, ZHANG Chuan-yong. FE Simulation of Bolt-up Process for Press-Retraining Bolts of HTR-PM Pressure Vessel[J]. Nuclear Power Engineering, 2011, 32(S1): 54-56.

PDF( 475 KB)

FE Simulation of Bolt-up Process for Press-Retraining Bolts of HTR-PM Pressure Vessel

1. Institute of Nuclear and New Energy Technology, Tsinghua University, Beijing, 100084, China;
2. Japan Technostar Company, Beijing Office, Beijing, 100098, China

Received Date: 2011-02-25
Rev Recd Date: 2011-05-18

Available Online: 2025-03-08

Abstract

Abstract

The reactor pressure vessel FE model with 42 M88 bolts is built in this study by ADVEN-TURECluster.These 42 bolts are divided into seven groups,and there are two steps in the bolt-up process.The simulation results show that every bolt-up step will make different influence to different groups of bolts.
- HTR-PM,
- Pressure vessel,
- Press-retraining bolts,
- Bolt-up,
- FE simulation

FullText(HTML)

References(0)

References

Relative Articles

[1]	Zhu Tenghao, Wang Hongtao, Wang Haitao. Research on Vibration-induced Noise Simulation of Main Control Room of High-temperature Gas-cooled Reactor[J]. Nuclear Power Engineering, 2024, 45(6): 132-138. doi: 10.13832/j.jnpe.2024.06.0132
[2]	Yu Xiaohuan, Du Juan, Shao Xuejiao, Yang Yu, Liu Zhenyu, Tian Jun, Yang Lingfang. Application of Master Curve in Reactor Pressure Vessle Ageing[J]. Nuclear Power Engineering, 2020, 41(2): 45-48.
[3]	Jin Dongjie, Wang Yin, Jin Gang, Geng Baojie, Guo Yunlong. Pre-Tightening Force Calibration Test Research for Stud without Measuring Rod of HTR-PM[J]. Nuclear Power Engineering, 2020, 41(6): 167-171.
[4]	Li Yinghong, Huang Hao, Zhou Rongsheng, Yang Xiaodong. Criticality Safety Calculation and Analysis of Fresh Fuel Element Transport Containers for High Temperature Gas-Cooled Reactor[J]. Nuclear Power Engineering, 2019, 40(6): 64-71. doi: 10.13832/j.jnpe.2019.06.0064
[5]	Jiang Zhuoer, Wang Haitao, Zhao Jun, Shi Li. Sensitivity Analysis for Seismic Fragilities of Lateral Supports of RPV for High Temperature Gas-Cooled Reactor[J]. Nuclear Power Engineering, 2018, 39(6): 53-58. doi: 10.13832/j.jnpe.2018.06.0053
[6]	Liu Yang, Wang Jun. Heat Transfer Simulation of Fuel Transport Cask for High Temperature Gas Cooled Reactor[J]. Nuclear Power Engineering, 2017, 38(5): 160-163. doi: 10.13832/j.jnpe.2017.05.0160
[7]	Zhang Jingcai, Hu Youming. Pressure for Hydrostatic Test of Pressure Vessel and Its Advantages and Disadvantages[J]. Nuclear Power Engineering, 2016, 37(4): 34-38. doi: 10.13832/j.jnpe.2016.04.0034
[8]	Bo Wen, Li Zhengcao, Wang Haitao, Shi Li. Research on Shape Optimization of RPV Opening of High Temperature Gas-Cooled Reactor Using Boundary Element Method[J]. Nuclear Power Engineering, 2016, 37(4): 24-27. doi: 10.13832/j.jnpe.2016.04.0024
[9]	Kuang Linyuan, Su Dongchuan, Wang Donghui, ZHeng Liangang, Shao Xuejiao. Effect of Interference Tolerance on Stress of Penetration of Reactor Pressure Vessel[J]. Nuclear Power Engineering, 2015, 36(S2): 131-134. doi: 10.13832/j.jnpe.2015.S2.0131
[10]	Shao Xuejiao, ZHeng Liangang, Su Dongchuan, Fu Xiaolong, Kuang Linyuan. Study on Finite Simulation Technology for Seal Ring of Reactor Pressure Vessel[J]. Nuclear Power Engineering, 2015, 36(S2): 142-145. doi: 10.13832/j.jnpe.2015.S2.0142
[11]	Chen Hao, Sun Kaibin, Wang Zhibing, Ding Zhanglong. Analysis of Radiation Sources ＆ Verifying of Radiation Level for Irradiated Surveillance Specimens of WWER1000 Reactor Vessel[J]. Nuclear Power Engineering, 2014, 35(6): 53-56. doi: 10.13832/j.jnpe.2014.06.0053
[12]	Yang Qingsong, Hao Zhonghang, Tang Chao. Design and Development of Special Tool for Installation of Seal Ring in Reactor Vessel[J]. Nuclear Power Engineering, 2014, 35(S1): 186-188.
[13]	Zhang Tao, Xiao Lingmei, Li Tenglong. Application of Statistical Process Control Technology in Pre-Stressing Analysis of Reactor Pressure Vessel Bolts[J]. Nuclear Power Engineering, 2014, 35(3): 51-54. doi: 10.13832/j.jnpe.2014.03.0051
[14]	ZHENG Liangang, LU Yongbo. Reliability Analysis of Reactor Pressure Vessel Intensity[J]. Nuclear Power Engineering, 2012, 33(4): 1-4.
[15]	LUO Qiang, XU Qi, ZHAO Jisong, REN Liping, CHEN Yong, MA Na. Aging Management of Reactor Pressure Vessel for PWR Nuclear Power Plants[J]. Nuclear Power Engineering, 2012, 33(S2): 114-119.
[16]	ZHENG Bin, ZANG Fenggang, SUN Yingxue. Pressurized Thermal Shock Analysis for Reactor Pressure Vessels[J]. Nuclear Power Engineering, 2012, 33(1): 1-3,13.
[17]	CAO Kemei, XU Yiquan, SHI Guobao, CAI Jianping. Analysis of Penetration Integrity under External Reactor Vessel Cooling[J]. Nuclear Power Engineering, 2011, 32(1): 1-5.
[18]	LIU Pan, JIN Ting, MAO Qing. Analysis on Fatigue Strength Reduction Factor of Reactor Pressure Vessel Flange Thread[J]. Nuclear Power Engineering, 2011, 32(S2): 9-12.
[19]	GUO Wuren, LIN Xiaoling, ZHENG Ningning. Method for Estimation of Activity in Decommissioned Nuclear Reactor Pressure Vessel[J]. Nuclear Power Engineering, 2011, 32(4): 114-117.
[20]	LIU Qingjiang, YE Tao. Study on Temperature Dropping during Pressure Vessel Discharge Process[J]. Nuclear Power Engineering, 2011, 32(4): 138-142.