Study on Feasibility of Replacing 321 with 316LN Stainless Steel for Main Reactor Coolant Pipe Material

LUO Yi-jun

Volume 34 Issue 5

Mar. 2025

Turn off MathJax

Article Contents

Abstract

References

Article Navigation > Nuclear Power Engineering > 2013 > 34(5): 80-83

LUO Yi-jun. Study on Feasibility of Replacing 321 with 316LN Stainless Steel for Main Reactor Coolant Pipe Material[J]. Nuclear Power Engineering, 2013, 34(5): 80-83.

Citation:

LUO Yi-jun. Study on Feasibility of Replacing 321 with 316LN Stainless Steel for Main Reactor Coolant Pipe Material[J]. Nuclear Power Engineering, 2013, 34(5): 80-83.

LUO Yi-jun. Study on Feasibility of Replacing 321 with 316LN Stainless Steel for Main Reactor Coolant Pipe Material[J]. Nuclear Power Engineering, 2013, 34(5): 80-83.

Citation:

LUO Yi-jun. Study on Feasibility of Replacing 321 with 316LN Stainless Steel for Main Reactor Coolant Pipe Material[J]. Nuclear Power Engineering, 2013, 34(5): 80-83.

PDF( 695 KB)

Study on Feasibility of Replacing 321 with 316LN Stainless Steel for Main Reactor Coolant Pipe Material

LUO Yi-jun

Nuclear Power Institute of China, Chengdu, 610041, China

Received Date: 2012-07-26
Rev Recd Date: 2013-03-16

Available Online: 2025-03-08

Abstract

Abstract

The metallurgical,physical and mechanical performance,and the corrosion and welding properties 0f 00Cr17Ni12Mo2（controlled Nitrogen,ANSI316LN） and 0Cr18Ni10Ti（ANSI321SS） for main pipe material were analyzed comparatively in this paper.The feasibility of 316LN pipe material manufacturing was studied too.The analysis results showed that under the operation condition of the nuclear reactor,the general properties of 316LN are better than that of 321SS.Therefore,316LN could be used for main pipe material,replacing 321SS.
- 316LN,
- 321SS,
- Replacing,
- Feasibility

FullText(HTML)

References(0)

References

Relative Articles

[1]	Hua Xinchao, Pan Deng, Li Yao, Peng Yipeng, Liu Jiaqing. Feasibility Study of 24-month Refueling for VVER[J]. Nuclear Power Engineering, 2025, 46(1): 24-29. doi: 10.13832/j.jnpe.2025.01.0024
[2]	Zhao Yuxiang, Xiong Ru, Liang Bo, Tang Rui. Experimental Study on Low-Cycle Fatigue Properties of Supercritical Water-cooled Reactor Candidate Cladding Material[J]. Nuclear Power Engineering, 2023, 44(5): 237-243. doi: 10.13832/j.jnpe.2023.05.0237
[3]	Su Haozhan, Chen Kai, Zhang Lefu, Dang Ying, Chen Le. Investigation on Corrosion Fatigue Behavior of 316LN SS under High Temperature Water Environment[J]. Nuclear Power Engineering, 2020, 41(1): 37-42. doi: 10.13832/j.jnpe.2020.01.0037
[4]	Su Genghua, Shi Xiaqing. Feasibility Study on Substitution of Primary Neutron Source with Secondary Neutron Source in PWRs[J]. Nuclear Power Engineering, 2020, 41(4): 22-25.
[5]	Chen Xingjiang, Peng Fang, Cong Guohui, Fu Wei, Luo Zhiyuan. Reserch of Optimal Integrated Verification Test Program for Shaft Seal Reactor Coolant Pump of 1000 MW Nuclear Power Plant[J]. Nuclear Power Engineering, 2020, 41(1): 113-116. doi: 10.13832/j.jnpe.2020.01.0113
[6]	He Xun, Zeng Chang, Yu Xiaoquan, Du Zhuoqi, Rafael Macián-Juan. Feasibility Study on Conceptual Design of Dual Fluid Fast Reactor[J]. Nuclear Power Engineering, 2019, 40(1): 42-47. doi: 10.13832/j.jnpe.2019.01.0042
[7]	Li Qi, SuN Lei, Jiang Xinliang. Research on Influence of Heating Temperature and Heat Treatment on Mechanical Property and Ultrasonic Test of 316LN Stainless Steel[J]. Nuclear Power Engineering, 2017, 38(S1): 31-33. doi: 10.13832/j.jnpe.2017.S1.0031
[8]	He Kun, Zhou Jun, Luo Qiang, Cheng Yong, Ren Liping, Zhu Yonghui. Study on Thermal Mechanical Fatigue Performance of 316LN Stainless Steel[J]. Nuclear Power Engineering, 2016, 37(4): 48-52. doi: 10.13832/j.jnpe.2016.04.0048
[9]	Wang Yongfu, Sun Yuliang. Technical-Economic Study on High Temperature Reactor for Combined Heat and Power Generation[J]. Nuclear Power Engineering, 2016, 37(3): 181-184. doi: 10.13832/j.jnpe.2016.03.0181
[10]	Kong Xiangwei, Qiu Fengxiang, Na Hongwei. Feasibility Study on Flow Test Procedure for AP1000 Accumulator Discharge Lines[J]. Nuclear Power Engineering, 2016, 37(2): 147-150. doi: 10.13832/j.jnpe.2016.02.0147
[11]	Yu Zhangcheng, Jie Heng. Feasibility Study on Application of Passive Safety System in Fusion-Fission Hybrid Energy Reactor[J]. Nuclear Power Engineering, 2015, 36(3): 129-134. doi: 10.13832/j.jnpe.2015.03.0129
[12]	Wang Zhixiao. Feasibility Analysis for Increasing Purification Flowrate during Plant Shutdown Oxygenation[J]. Nuclear Power Engineering, 2015, 36(3): 120-124. doi: 10.13832/j.jnpe.2015.03.0120
[13]	Deng Qimin, Yin Bangshun, Cheng Zuoyong, Li Mingqi, Li Maoliang. Feasibility Study on Application of Polyantimonic Acid in ⁹⁰Y Generator Preparation[J]. Nuclear Power Engineering, 2014, 35(1): 174-177.
[14]	Zhang Shixun, Zou Tingting, Zhang Hong, Pan Hui. Feasibility Study on Fuel Management with Dual-Enrichment 18 Months Refueling[J]. Nuclear Power Engineering, 2014, 35(S2): 203-206. doi: 10.13832/j.jnpe.2014.S2.0203
[15]	Yang Lei, Li Shuliang, Yi Qiaoling, Xiong Jing. Feasibility Study on Acoustic Emmission Technology Monitoring for New Pattern Steam Generator[J]. Nuclear Power Engineering, 2014, 35(6): 115-119. doi: 10.13832/j.jnpe.2014.06.0115
[16]	Luo Qiang, CheN Yong, Qiu Shaoyu, Zhou Jun, He Kun. Study on Low Temperature Thermal Aging Behavior of 316LN Austenitic Stainless Steel Weld[J]. Nuclear Power Engineering, 2014, 35(4): 102-105. doi: 10.13832/j.jnpe.2014.04.0102
[17]	KONG Jing-song, GUO Wei-qun. Feasible Research on VLLW Disposal in Control Area of Nuclear Installation[J]. Nuclear Power Engineering, 2013, 34(3): 172-174.
[18]	CHEN Wen-jun, JIANG Sheng-yao. Feasibility Study on Development of Small Nuclear Power Reactors in China[J]. Nuclear Power Engineering, 2013, 34(2): 153-156.
[19]	DENG Qi-min, CHENG Zuo-yong, LI Mao-liang, ZHANG Jing-song, CHEN Yun-ming. Feasibility Research of ⁹⁹Mo,³¹I and ⁸⁹Sr Production by Medical Isotope Production Reactor[J]. Nuclear Power Engineering, 2011, 32(6): 115-118,124.
[20]	KANG Huan-ju, YANG Shuang, SUN Hua. Experimental Study on Stress Corrosion Cracking of 316LN[J]. Nuclear Power Engineering, 2011, 32(6): 101-104,114.